Riding Lawn Mower Review: Yard-Man 13A0785T055

Featured

Posted on by
Reply

Packed with power and durability, those who wish to upgrade their riding lawn mower may want to try out Yard-Man 13A0785T055. This tractor mower features superior grass cutting technology to achieve professionally trimmed lawn. Ideal for residential and small commercial spaces, the Yard-Man mower provides an impressive result as with professional lawn mowers. Now, you can make the then arduous and tiring task of mowing the lawn enjoyable with this new equipment.

To get the best out of your investment, reading several Yard-Man riding lawn mower reviews may shed light on the product. It helps you in deciding which particular brand or model to buy. Meanwhile, let’s talk about the Yard-Man 13A0785T055 and the key features, plus pros and cons of this much talked about equipment.

Product Overview

The Yard-Man 13A0785T055 46-inch ride mower operates with an auto-drive transmission. Powered by a 19.5-horsepower Briggs and Stratton Powerbuilt engine, this equipment cuts down your mowing time. It also features an easy-to-operate PTO clutch for increased efficiency and ergonomically designed foam padded seat for comfort.

Key features include: 46-inch deck with two deck wheels designed to cover all types of lawn terrains; 2-blade system that cuts tall and thick grass easily; superior maneuverability; and durability that guarantees excellent condition after years of regular use.

However, the main drawback of Yard-Man 13A0785T055 is its failure to comply the California Air Resourced Board (CARB) regulations, thus making it unavailable in the said state. CARB is the clean air agency of California monitoring the air pollution level in different industries, setting industrial standards to fulfill the clean air act, and granting permissions to smoke-emitting products that have passed the criteria.


Pros of the Yard-Man 13A0785T055 46-Inch 19.5 HP Powerbuilt Auto-Drive Transmission Riding Lawn Mower:

  • Features the powerful 19.5 HP Briggs and Stratton Powerbuilt engine, ideal for most residential and commercial lawns
  • Runs smoothly with auto-drive transmission
  • Wide deck for optimum performance
  • Easy-to-handle manual PTO clutch
  • Tough wheels that provides better traction in different lawn terrains
  • Durable components
  • Excellent maneuverability


Cons of the Yard-Man 13A0785T055 46-Inch 19.5 HP Powerbuilt Auto-Drive Transmission Riding Lawn Mower:

  • Won’t mow in reverse gear
  • Not eco-friendly enough to pass the regulations set by CARB

Most Yard-Man reviews from actual users highlight the model’s grass cutting power and durability. In fact, many of them attest to make their future purchase for replacement still a Yard-Man brand.

However, there are some Yard-Man owners who aren’t happy with the 2-blade system compared to several tractor mowers that have 3-blade system. Some of them also complain about the bulkiness of the equipment, leaving them with storing issues. A bit of advice for buyers: always consider the size of your lawn and storing space before buying a riding mower.

Truly a value for money, the Yard-Man 13A0785T055 can be your ideal riding lawn mower. Whether for mere grass trimming or for clearing out weeds of unkempt lawns, the Yard-Man riding lawn mower is the perfect companion in gardening.

Buy Yard-Man 13A0785T055 46-Inch 19.5 HP Powerbuilt Auto-Drive Transmission Riding Lawn Mower

Solar Water Heating and Bathroom Remodeling

Featured

Posted on by
Reply

Here are three easy steps to a solar water heater for your tub.

  • Move to a part of the world that’s consistently hot and sunny, like the Middle East.
  • Install your tub on the roof and fill it with water.
      • Wait a day, and then enjoy your warm bath.

    No? Okay, but a similar principal is involved if you live in America, in a state that has actual seasons, and your tub is enclosed in an indoor bathroom. Your bathroom remodeling project can, and should, involve solar powered water heating. You’ll be saving money, and the earth, by lessening your reliance on fossil fuels.

    solar water heating

    Solar Water Heating

    Solar powered water heating is a very real option for all of us, even during the cold months, and even at night. Solar panels on roofs are common in Greece, Japan, Turkey, Australia and Israel, and not all of those climates can claim consistent sunshine 365 days a year.

    It’s time we saved some money, and cut back on non-renewable resources, by investing in solar power when we do our bathroom remodeling. Technology has evolved since the late 1800s, when water tanks, painted black, were perched on a home’s roof to absorb some of the sun’s rays. In fact, technology can now provide hot water, courtesy of the heat of the sun, using two different systems. The passive system, called the compact system, and the active system, called the pump system, with the occasional back-up of an auxiliary energy source, can easily provide hot water at any time of day, in any season, for you and your family.

    Which system you need depends on where you live. The change in temperature between day and night, and between summer and winter, will factor into your bathroom remodeling plans for installing solar water heating. The possibility of the water overheating, and the possibility of the water freezing, are also climate factors to consider.
    Passive systems circulate warm water during consistently warm seasons, and if you live in Florida or Southern California, this can be an easy and inexpensive system to install. Active systems, however, circulate the water using pumps, and contain antifreeze valves or drainback tanks to prevent the stored water from getting so cold that the pipes would burst.

    The active system allows for the homeowner to have control over the pump and the temperature with a programmable, electronic controller, which can often also calculate and log how much energy has been saved. The controller reports the difference in temperature between the collected water, heated with solar power, and the water in the storage tank. Typically, the pump will be activated when the collected water is ten degrees warmer than the stored water.

    When the water gets too cold, an antifreeze system, using nontoxic propylene glycol, circulates the glycol to prevent freezing. Or, a drain-back reservoir collects the water inside the home and holds it while the outdoor temperature is low.

    The active system is more expensive to install, although do-it-yourself kits are widely available and instructions for installation can be found on the internet. If you have a solar water heating system installed professionally during your bathroom remodeling project, you may not offset the installation cost with your energy bill savings for several years. But in several years, you’ll thank yourself. The earth will thank you too.

    Special thanks to Budget Bath for this informative article. Please visit their website here, Bathroom Remodeling MD.

    How To Install Crown Molding

    Featured

    Posted on by
    Reply

    Difficulty level – Beginner

    Learning how to install crown molding can provide a two fold advantage to you; being able to save money by not having to hire a professional home improvement company to install crown moldings for you, and the satisfaction of improving your own home with your own hands.

    By knowing the correct installation steps and being comfortable with doing basic home improvements in your home, you will not have to hire a contractor anymore to do the job for you. Contractors usually charge a high price, and their labor is a rather high proportion of the total cost of crown molding installation. Why not do it yourself and save?

    Before you get started, you should prepare for the job, first.


    The Preparations

    1. Take the measurements and add ten percent to the figures for when you make mistakes.

    2. Choose the style and finish that you want. Many sizes and shapes are available for you to choose from. Make sure that they match with your personal preferences, living room decorations, and the overall color scheme. The finish that you choose should be applied first before you begin cutting and fitting the crown molding.

    3. Buy the size that will need the least amount of splices. Splices may be unavoidable in some cases, but the fewer splices there are, the more appealing the end results will be.


    Cutting The Corners

    1. The first and most difficult part in learning how to install crown molding is cutting the corners. The easiest way to trim the corners is by using a coping saw, since a mitered joint is less tight than a coped joint. If there is any gap in a coped cut, this can be concealed with some caulk.

    2. Another tool that you can choose to cut the corners is a power miter saw. Not only is it accurate, it also provides a cleaner cut.


    Measuring And Marking The Wall

    Take the measurements of the wall for the length of the very first piece of molding. You have to mark the wall so that it shows the bottom edge of the molding.

    Cutting The Pieces

    1. After determining the length of the molding, cut it in a straight line at a ninety degree angle. This will make both ends hit against the side walls.

    2. Cut the next piece so it fits an inside corner. You can do this by moving the miter saw guide to the forty-five degree angle point and then setting the molding into place.

    3. Know how the pieces fit together. The edge against the vertical fence is the bottom part of the molding while the edge against the table is the top. Imagine that your table is the ceiling.

    4. Cut the molding at a perfect forty-five degree angle using a ten inch saw blade. For an inside corner, the bottom should be longer than the top. For an outside corner, the top should be longer than the bottom.

    Coping The Joint

    When you cope a joint, you have to scribe the end of one molding to the face of another. Mark the front edge using a pencil, and then with the help of a coping saw, cut as close to the line as possible. Be sure to cut at a slight angle.

    Checking For Gaps

    Any gaps that have to be trimmed will be revealed if the fit is checked against a scrap piece of molding. To get rid of these gaps, cut off the high points using the coping saw.

    Attaching The Molding

    The last part on how to install crown molding is attaching the molding. Take the molding to the wall once the fit is perfect. You will need some help holding a long piece. Attach it to the wall by pushing the end into the corner. Ensure that the fit is as tight as possible. If there are any gaps, cover them using a caulk gun. Use optional blocks to cover the spot where the outside corners should meet.